We have a PM3, v.3.7.2. One port is used for ISDN connections, and the
other E1 port is used for Frame Relay connectin (or will be used).
Unfortunately there is a problem in Frame Relay connectin.
Configuration is as follows:
----------------------- Current Status - Port W32
---------------------------
Status: ESTABLISHED
Input: 54560 Abort Errors: 0
Output: 263152 CRC Errors: 3314
Pending: 0 Overrun Errors: 0
TX Errors: 0 Frame Errors: 0
Modem Status: DCD+ CTS+
Active Configuration Default Configuration
-------------------- ---------------------
Port Type: Netwrk Netwrk (Hardwired)
Line Speed: Ext 2048K Ext Clock
Modem Control: on on
Local Address: 194.54.59.32 194.54.59.32
Netmask: 255.255.255.252 255.255.255.252
Interface: frm32 (FRM,Listen) (FRM,Quiet)
Mtu: 1500 1500
Dial Group: 1
Annex-D Poll: 15 (seconds)
Old DLCI List: 32:194.54.59.33
IP DLCI's: DLCI Address
----- ------------
16 0.0.0.0
As you see, the port status is ESTABLISED.
and sh line1 command gives
sh line1
---------------------- line1 - E1 2.048 Mbps ---------------
Status: UP F1 Framing: FAS Encoding: HDB3 PCM: a-law
Violations
-----------------------------
Bipolar 1
CRC4 0
E-bit 8
FAS bit 0
The problem is that: status of connection changes ESTABLISED to CONNECTING
too often. It tries for a while, saying CONNECTING, and then goes to state
of ESTABLISED. But for a while, then goes to CONNECTING.. surely this is
not desired thing, and using this line as a main Internet connection is not
possible.
set debug 0x51 gives logs as :
(W32) LMI-AnnexD: Received Full Status - Sequence 11
(W32) Annex-D: Sending Full Status Enquiry - Sequence 26
(W32) Annex-D: Sending Full Status Enquiry - Sequence 27
(W32) Annex-D: Sending Full Status Enquiry - Sequence 28
(W32) Annex-D: Sending Full Status Enquiry - Sequence 29
(W32) Annex-D: Sending Full Status Enquiry - Sequence 30
(W32) Annex-D: Sending Full Status Enquiry - Sequence 31
(W32) Annex-D: Sending Full Status Enquiry - Sequence 2
(W32) Annex-D: Sending Full Status Enquiry - Sequence 3
(W32) Annex-D: Sending Full Status Enquiry - Sequence 4
(W32) Annex-D: Sending Full Status Enquiry - Sequence 5
(W32) Annex-D: Sending Full Status Enquiry - Sequence 6
(W32) Annex-D: Sending Full Status Enquiry - Sequence 7
(W32) Annex-D: Sending Full Status Enquiry - Sequence 8
(W32) LMI-AnnexD: Received Full Status - Sequence 16
(W32) Annex-D: Sending Sequence Exchange - Sequence 9
(W32) Annex-D: Sending Full Status Enquiry - Sequence 10
(W32) Annex-D: Sending Full Status Enquiry - Sequence 11
and goes on.
Do you have any idea about the problem ?
ps* the other side is also a PM3.
Sincerely.
balci.
-
To unsubscribe, email 'majordomo@livingston.com' with
'unsubscribe portmaster-users' in the body of the message.
Searchable list archive: <URL:http://www.livingston.com/Tech/archive/>