BSP set up at 115200k, 8/N/1, CTS/RTS bi, Answer 64k Data. It is
attached to port s17 which is configured as follows:
----------------------- Current Status - Port S17 ---------------------------
Status: IDLE
Input: 414925 Parity Errors: 0
Output: 20550 Framing Errors: 113
Pending: 0 Overrun Errors: 0
Modem Status: DCD- CTS+
Active Configuration Default Configuration
-------------------- ---------------------
Port Type: Netwrk Netwrk (Dial In & Out) (Security)
Baud Rates: 115200 115200,115200,115200
Flow Control: RTS/CTS RTS/CTS
Modem Control: on on
Modem Config: None bsp
Interface: Unassigned (SLIP,Listen (SLIP,Quiet)
Mtu: 0 1500
Dial Group: 0
Pipe 75 is set up as follows: Software +5.1Ap8+
Ethernet
Connections
20-101 trace
>Station=trace
Active=Yes
Encaps=PPP <--also tried MPP and MP
Dial #=3621740
Calling #=
Called #=
Route IP=Yes
Route IPX=N/A
Bridge=N/A
Dial brdcast=N/A
Encaps options...
Send Auth=PAP
Send PW=********
Recv PW=N/A
MRU=1500
LQM=No
LQM Min=600
LQM Max=600
Link Comp=None
VJ Comp=Yes
Split Code.User=N/A
Ip options...
LAN Adrs=0.0.0.0/0 <--initially tried putting PM's address here
WAN Alias=0.0.0.0
IF Adrs=205.240.224.35/32 <--initially tried leaving this empty
Preference=60
Metric=1
DownPreference=0
DownMetric=7
Private=No
RIP=Off
Client Pri DNS=0.0.0.0
Client Sec DNS=0.0.0.0
Client Assign DNS=No
Client Gateway=0.0.0.0
Ipx options...
Session options...
Telco options...
AnsOrig=Call Only
Callback=No
Exp Callback=No
Callback Delay=N/A
Call Type=Switched
Group=N/A
FT1 Caller=N/A
Data Svc=64K
Force 56=No
Bill #=
My radius entry looks like:
trace Password = "Password"
User-Service-Type = Framed-User,
Session-Timeout = 0
Framed-Protocol = PPP,
Framed-Address = 205.240.224.33,
Framed-Netmask = 255.255.255.248,
Framed-Route = "205.240.224.34 205.240.224.33 1"
Framed-Routing = None,
Framed-Filter-Id = "tracefilter",
Framed-MTU = 1500
I set debug 0x51 and got the following when I tried to dial in:
Sending LCP_CONFIGURE_REQUEST to port S17 of 24 bytes containing:
01 01 00 18 02 06 00 00 00 00 05 06 5f bc a5 ad
07 02 08 02 03 04 c0 23
Received LCP_CONFIGURE_REJECT on port S17 of 10 bytes containing:
04 01 00 0e 05 06 5f bc a5 ad 07 02 08 02
Sending LCP_CONFIGURE_REQUEST to port S17 of 14 bytes containing:
01 02 00 0e 02 06 00 00 00 00 03 04 c0 23
Received LCP_CONFIGURE_ACK on port S17 of 10 bytes containing:
02 02 00 0e 02 06 00 00 00 00 03 04 c0 23
Received LCP_CONFIGURE_REQUEST on port S17 of 14 bytes containing:
01 4d 00 12 01 04 06 40 02 06 00 00 00 00 03 04
c0 23
Sending LCP_CONFIGURE_NAK to port S17 of 9 bytes containing:
03 4d 00 09 03 05 c2 23 05
Received LCP_CONFIGURE_REQUEST on port S17 of 10 bytes containing:
01 4e 00 0e 01 04 06 40 02 06 00 00 00 00
Sending LCP_CONFIGURE_ACK to port S17 of 14 bytes containing:
02 4e 00 0e 01 04 06 40 02 06 00 00 00 00
S17: LCP Open
and 'show sessions' shows this:
S17 PPP - Netwrk In CONNECTING 0 0
After about 45 seconds the connection is dropped and the BitSurfr resets.
If I understood the debug output, I could probably solve this myself.
Sorry if this is an obvious fix. I've been screwing with this for 2
days now and have gotten no closer. Any help would be most appreciated
as I am close to losing this customer.
======================================================================
When I was a kid, I had two friends, and they were imaginary
and they would only play with each other
======================================================================
Greg Mead - MeadNet - PO Box 1161 - Bradenton, FL 34206 - 941-746-8933
-
To unsubscribe, email 'majordomo@livingston.com' with
'unsubscribe portmaster-users' in the body of the message.
Searchable list archive: <URL:http://www.livingston.com/Tech/archive/>