> I'm trying to set up my first PM2ER-10. Having tons of troubles. I have
> set up several Ciscos and never had these kinds a problems.
>
> Here is everything I could think of to show people....
>
> System Name: wausa
> Default Host: 0.0.0.0
> Alternate Hosts:
> IP Gateway: 199.240.128.222
> Gateway Metric: 1
> Default Route: Quiet (Off)
> Name Service: DNS
> Name Server: 199.240.128.193
> Domain: bloomnet.com
> Telnet Access Port: 23
> Loghost: 199.240.128.193
> Assigned Address: 0.0.0.0
> RADIUS Server: 199.240.128.193
> Alternate Server: 0.0.0.0
> Accounting Server: 0.0.0.0
> Alt. Acct. Server: 0.0.0.0
> Disabled Modules: SNMP
> wausa> show w1
> ----------------------- Current Status - Port W1 ---------------------------
> Status: ESTABLISHED
> Input: 172009 Abort Errors: 0
> Output: 95256 CRC Errors: 0
> Pending: 0 Overrun Errors: 0
> TX Errors: 0 Frame Errors: 0
> Modem Status: DCD+ CTS+
>
> Active Configuration Default Configuration
> -------------------- ---------------------
> Port Type: Netwrk Netwrk (Hardwired)
> Line Speed: Ext 56K Ext Clock
> Modem Control: off off
> Local Address: 199.240.129.22 199.240.129.22
> Netmask: 255.255.255.252 255.255.255.252
> Interface: frmW1 (FRM,Routing) (FRM,Routing)
> Mtu: 1500 0
> LMI Poll Int: 10 (seconds)
> DLCI List: 16
> Dial Group: 0
>
>
> Setting debug value to 0x51
> (W1) LMI: Sending Sequence Exchange - Sequence 112
> (W1) LMI: Received Sequence Exchange - Sequence 111
> (W1) LMI: Sending Sequence Exchange - Sequence 113
> (W1) LMI: Received Sequence Exchange - Sequence 112
> (W1) LMI: Sending Sequence Exchange - Sequence 114
> (W1) LMI: Received Sequence Exchange - Sequence 113
> (W1) LMI: Sending Sequence Exchange - Sequence 115
> (W1) LMI: Received Sequence Exchange - Sequence 114
> (W1) LMI: Sending Full Status Enquiry - Sequence 116
> (W1) LMI: Received Full Status - Sequence 115
> DLCI List: 16
> (W1) LMI: Sending Sequence Exchange - Sequence 117
> (W1) LMI: Received Sequence Exchange - Sequence 116
> (W1) LMI: Sending Sequence Exchange - Sequence 118
> (W1) LMI: Received Sequence Exchange - Sequence 117
> (W1) LMI: Sending Sequence Exchange - Sequence 119
> (W1) LMI: Received Sequence Exchange - Sequence 118
> (W1) LMI: Sending Sequence Exchange - Sequence 120
> (W1) LMI: Received Sequence Exchange - Sequence 119
> (W1) LMI: Sending Sequence Exchange - Sequence 121
> (W1) LMI: Received Sequence Exchange - Sequence 120
> (W1) LMI: Sending Full Status Enquiry - Sequence 122
> (W1) LMI: Received Full Status - Sequence 121
> DLCI List: 16
> (W1) LMI: Sending Sequence Exchange - Sequence 123
> (W1) LMI: Received Sequence Exchange - Sequence 122
> (W1) LMI: Sending Sequence Exchange - Sequence 124
> (W1) LMI: Received Sequence Exchange - Sequence 123
> (W1) LMI: Sending Sequence Exchange - Sequence 125
> (W1) LMI: Received Sequence Exchange - Sequence 124
> (W1) LMI: Sending Sequence Exchange - Sequence 126
> (W1) LMI: Received Sequence Exchange - Sequence 125
> (W1) LMI: Sending Sequence Exchange - Sequence 127
> (W1) LMI: Received Sequence Exchange - Sequence 126
> (W1) LMI: Sending Full Status Enquiry - Sequence 128
> (W1) LMI: Received Full Status - Sequence 127
> set console 0x0
> wausa> res(W1) LMI: Sending Sequence Exchange - Sequence 131
> e(W1) LMI: Received Sequence Exchange - Sequence 130
> t console
> Console RESET
>
> I know I'm missing something, but I can't figure it out! I also have a
> ticket opened with Livingston, but would like some feedback if people
> have some time. TIA
>
> --Josh
>
> ====================================================================
> Joshua Barney -- josh@bloomnet.com Northeast Nebraska ComNet
> Network Administrator (402) 373-4603
> 1-800-359-2981
> http://www.bloomnet.com
>
>
--Josh
====================================================================
Joshua Barney -- josh@bloomnet.com Northeast Nebraska ComNet
Network Administrator (402) 373-4603
1-800-359-2981
http://www.bloomnet.com