Quick Start Guide for PM-3 CT 1/PRI Circuits

QUICK SET-UP FOR PORTMASTER 3 FOR CT1/PRI CIRCUITS

Introduction
This is a Quick Set-up guide for configuring a PortMaster 3^TM to connect to your network. To demonstrate how to set up both Channelized CT1 and PRI services, this guide identifies line0 as configured for Channelized T1 and line1 for PRI service. In your actual setup, you may choose a single service (Channelized T1 or PRI) for both line0 and line1. Many of the values placed in the commands on this sheet are provided as examples. Please insert your actual values during set-up.

PortMaster 3 Quick Set-up Guide for Channelized T1 and PRI
Note: Do not over-configure the PM3. The port settings and modem settings run best using default values. Also customer specific applications, such as Channelized CT1 and Multichassis Multilink PPP, are higlighted. Only if you plan to implement any of these specific feature do you need to utilize the commands associated with them.

Use the console port to login. login: !root hit return twice to get to the Command prompt.

General configurations set sysname ISP-PM3-1 #PortMaster name set address 192.168.100.1 #address of PortMaster set netmask 255.255.255.0 #netmask of Ethernet set gateway 192.168.100.254 #default gateway address set loghost 192.168.1.2 #sets the syslog host (optional) set domain ISP.net #domain name (optional) set namesvc dns #dns name service (optional) set nameserver 192.168.25.16 #address name server (optional) set assigned 192.168.100.33 #first number of dynamic pool set broadcast high #set RIP broadcast to ones set default off #do not broadcast or listen for default routes set routing on #listen and broadcast RIP RADIUS configurations set authentic 192.168.120.10 #RADIUS server address set secret asecret #RADIUS secret in /etc/raddb/clients set accounting 192.168.120.10 #RADIUS server accounting ChoiceNet configurations set choicenet 192.168.120.10 #ChoiceNet server address set choicenet-secret anothersecre #ChoiceNet secret in #/etc/choicenet/clients Channelized T1 configurations set line0 inband #line0 CH-T1 inbound calls set line0 signaling wink #"wink" ,"fxs" , or "immediate" set line0 framing ESF #"ESF" or "D4" set line0 encode B8ZS #"B8ZS" or "AMI" ISDN PRI configurations* set line1 isdn #set line1 to PRI set isdn-switch dms #dms100 | ni-2 | att-5ess Multichassis Multilink PPP configurations set endpoint 00c0050402fa #enable multichassis MPPP #specification is the MAC address of ether 0 save all #Save config to nonvolatile mem reboot** #restarts the PM3 Configuration is complete at this point. *Line0 and line1 are PRI ready by default. **A reboot may be required if you decide to use CTI.
If you are unable to configure the PortMaster 3 based on this Quick Set-up Guide or the accompanying manuals, please contact Technical Support at 800-458-9966(available in the U.S. only) or 510 737 2100.

Quick Set-up for Portmaster 3: Appendix

The following information is for reference and troubleshooting.
To view system level messages from a Telnet session use the following command.
ISP-PM3-1>set console

Note: Reset this when you are done by using the command "reset console".

To view your configuration use the following commands. ISP-PM3-1>show global ISP-PM3-1>show ether0 ISP-PM3-1>show all ISP-PM3-1>show line0 (line1) ISP-PM3-1>show modem ISP-PM3-1>show mx (where x is the "modem" to be viewed) ISP-PM3-1>show mc ISP-PM3-1> show global System Name: ISP-PM3-1 Default Host: 0.0.0.0 Alternate Hosts: IP Gateway: 192.168.100.254 Gateway Metric: 1 Default Routing: Quiet (Off) Name Service: DNS Name Server: 192.168.25.16 Domain: ISP.net Telnet Access Port: 23 Loghost: 192.168.1.2 Maximum PMconsole: 1 Assigned Address: 192.168.100.33 RADIUS Server: 192.168.120.10 Alternate Server: 0.0.0.0 Accounting Server: 192.168.120.10 Alt. Acct. Server: 0.0.0.0 PPP Authentication: PAP: on CHAP: on ISDN Switch Type: DMS-100 End Point Disc: 00c0050402fa Disabled Modules: SNMP OSPF ISP-PM3-1> show ether0 Ethernet Status: IP - Enabled IPX - Disabled Interface Addr: 192.168.100.1 Netmask: 255.255.255.0 Broadcast Address: 192.168.100.255 IPX Network: 00000000 IPX Frame Type: ETHERNET_802.2 Ethernet Address: 00:c0:05:04:02:fa Routing: RIP(Broadcast) Input Filter: Output Filter: ISP-PM3-1> show all Local Addr: 192.168.100.1 Default Host: 0.0.0.0 Gateway: 192.168.100.254 Netmask: 255.255.255.0 DNS Server: 192.168.25.16 Domain: ISP.net Port Speed Mdm Host Type Status Input Output Pend ---- ------ ---- ------ ------- -------- -------- ------- ---- C0 9600 off Login USERNAME 0 30 0 S0 28800 M0 ptp0 Netwrk ESTABLISHED 2640979 28672048 0 S1 26400 M43 ptp1 Netwrk ESTABLISHED 118793396 3159866 0 S2 31200 M41 ptp2 Netwrk ESTABLISHED 6596211 52321586 0 S3 28800 M2 ptp3 Netwrk ESTABLISHED 8004509 38295849 0 S4 26400 M37 ptp4 Netwrk ESTABLISHED 3534285 30490344 0 S5 28800 M1 ptp5 Netwrk ESTABLISHED 3136302 37014991 0 S6 33600 M27 ptp6 Netwrk ESTABLISHED 7784788 31805262 0 S7 28800 M23 ptp7 Netwrk ESTABLISHED 4316154 52130507 0 S8 21600 M4 ptp8 Netwrk ESTABLISHED 3056758 33047779 0 S9 31200 M3 ptp9 Netwrk ESTABLISHED 6639395 40367740 0 ISP-PM3-1> show line0 ------------------------ line0 - T1 Inband DS0 -------------------- Status: UP Framing: ESF Encoding: B8ZS PCM: u-law Signaling: Trunk E&M wink start Receive Level: +2dB to -7.5dB Alarms Violations ------------------------------------ -------------------------------- Blue 0 Bipolar 0 Yellow 1 CRC Errors 0 Receive Carrier Loss 0 Multiframe Sync 0 Loss of Sync 0 ISP-PM3-1> show line1 -------------------------------------line1 - T1 Primary Rate ISDN ------ Status: UP Framing: ESF Encoding: B8ZS PCM: u-law Receive Level: -7.5dB to -15dB Alarms Violations ------------------------------ ----------------------------- Blue 0 Bipolar 0 Yellow 1 CRC Errors 0 Receive Carrier Loss 0 Multiframe Sync 0 Loss of Sync For futher information, consult the reference manual,
Command Line Administrator's Guide. ISP-PM3-1> show modem Mdm Port Status Speed Compression Protocol Calls Retrain Disconnect ---- ----- -------- ----- ------------ -------- ----- ------- ---------- M0 S2 ACTIVE 28800 V42BIS LAPM 2 0 NORMAL M1 S3 ACTIVE 28800 V42BIS LAPM 1 0 NORMAL M2 S4 ACTIVE 33600 V42BIS LAPM 1 0 NORMAL M3 READY UNKNWN NONE NONE 0 0 NORMAL . . . ISP-PM3-1> show m0 State: ACTIVE Active Port: S2 Transmit Rate: 28800 Receive Rate: 28800 Connection Type: LAPM/V42BIS Chars Sent: 8537870 Chars Received: 7563501 Retrains: 0 Renegotiations: 0 Total Calls: 3 Modem Detects: 3 Good Connects: 3 Connection Failures No Modulation: 0 No Protocol: 0 Not Operational: 0 Total Failed: 0 Session Terminations Lost Carrier: 0 Normal Disconnect: 2 ISP-PM3-1> sh mc Neighbors: 192.168.1.1 192.168.1.2 Port User Host/Inet/Dest Type Peer ------- ------- --------------------- ------- ------ S22 user1 192.168.1.21 SLAVE 192.168.1.1 VO user2 192.168.1.200 VIRTUAL 192.168.1.2 For more information on debugging, consult the reference manual, Command Line Administrator's Guide. ISP-PM3-1>set console To clear debug commands. ISP-PM3-1>set debug off ISP-PM3-1>reset console Thank you for using Lucent products in your network.