QUICK SET-UP FOR PORTMASTER 3
FOR E1/PRI CIRCUITS

Introduction

This is a Quick Set-up guide for configuring a PortMaster 3TM to connect to your network. To demonstrate how to set up E1 and PRI service, this guide identifies line0 for PRI service. Many of the values placed in the commands on this sheet are provided as examples. Please insert your actual values during set-up.

PortMaster 3 Quick Set-up Guide for E1/PRI

Note: Do not over-configure the PM3. The port settings and modem settings run best using default values. Also customer specific applications, such as Multichassis Multilink PPP, are highlighted. Only if you plan to implement any of these specific features do you need to utilize the commands associated with them.

Use the console port to login. login: !root hit return twice to get to the Command prompt.


General configurations
set sysname ISP-PM3-1
#PortMaster name
set address 192.168.100.1
#address of PortMaster
set netmask 255.255.255.0
#netmask of Ethernet
set gateway 192.168.100.254
#default gateway address	
set loghost 192.168.1.2
# sets the syslog host (optional)
set domain ISP.net
#domain name (optional)
set namesvc dns
#dns name service (optional)
set nameserver 192.168.25.16
#address name server (optional)
set assigned 192.168.100.33
#first number of dynamic pool
set broadcast high
#set RIP broadcast to ones
set default off
#do not broadcast or listen for default routes
set routing on
#listen and broadcast RIP
RADIUS configurations
set authentic 192.168.120.10
#RADIUS server address
set secret asecret
#RADIUS secret in /etc/raddb/clients
set accounting 192.168.120.10
#RADIUS server accounting
ChoiceNet configurations
set choicenet 192.168.120.10
#ChoiceNet server address
set choicenet-secret anothersecret
#ChoiceNet secret in
/etc/choicenet/clients
ISDN PRI configurations*
set line0 isdn
#set line0 to PRI
set line0 pcm a-law			
set isdn-switch net5
#net5 | vn2 | vn3 | ltr6 | ntt | kdd
set line0 framing crc4
#crc4 | fas
set line0 encoding hdb3
#hdb3 | ami			
Multichassis Multilink PPP configurations
set endpoint 00c0050402fa
#enable multichassis MPPP
#specification is the MAC address of ether 0
save all
#Save config to nonvolatile mem
reboot
#restarts the PM3


Configuration is complete at this point.

*Line0 and line1 are PRI ready by default.

If you are unable to configure the PortMaster 3 based on this Quick
Set-up Guide or the accompanying manuals, please contact
Enterprises Technical Support at 800-458-9966 (available in the U.S. only) or
510-737-2100.

Quick Set-up for Portmaster 3: Appendix


The following information is for reference and troubleshooting.

To view system level messages from a Telnet session use the following
command.

ISP-PM3-1>set console

Note: Reset this when you are done by using the
command "reset console".

To view your configuration use the following commands.

ISP-PM3-1>show global
ISP-PM3-1>show ether0
ISP-PM3-1>show all
ISP-PM3-1>show line0 (line1)
ISP-PM3-1>show modem
ISP-PM3-1>show mx (where x is the "modem" to be viewed)
ISP-PM3-1>show mc
ISP-PM3-1> show  global
System Name: ISP-PM3-1
Default Host: 0.0.0.0
Alternate Hosts:
IP Gateway: 192.168.100.254
Gateway Metric: 1
Default Routing: Quiet (Off)
Name Service: DNS
Name Server: 192.168.25.16
Domain: ISP.net
Telnet Access Port: 23
Loghost: 192.168.1.2
Maximum PMconsole: 1
Assigned Address: 192.168.100.33
RADIUS Server: 192.168.120.10
Alternate Server: 0.0.0.0
Accounting Server: 192.168.120.10
Alt. Acct. Server: 0.0.0.0
PPP Authentication: PAP: on    CHAP: on
ISDN Switch Type: DMS-100
End Point Disc: 00c0050402fa
Disabled Modules: SNMP OSPF
ISP-PM3-1> show ether0
   Ethernet Status: IP - Enabled   IPX - Disabled
   Interface Addr: 192.168.100.1
          Netmask: 255.255.255.0
Broadcast Address: 192.168.100.255
      IPX Network: 00000000
   IPX Frame Type: ETHERNET_802.2
 Ethernet Address: 00:c0:05:04:02:fa
          Routing: RIP(Broadcast)
     Input Filter:
    Output Filter:
ISP-PM3-1> show all
Local Addr: 192.168.100.1			 Default Host: 0.0.0.0
   Gateway: 192.168.100.254                      Netmask: 255.255.255.0
DNS Server: 192.168.25.16                        Domain: ISP.net

Port  Speed	Mdm  Host  Type	   Status       Input	Output	  Pend
----  --------	---  ----  ----   --------	-------  ------  -----

C0    9600 	off         Login  USERNAME   	0         30          0	
S0   28800 	M0  ptp0    Netwrk ESTABLISHED 	2640979   28672048    0
S1   26400 	M43 ptp1    Netwrk ESTABLISHED 	11879339  63159866    0
S2   31200 	M41 ptp2    Netwrk ESTABLISHED  6596211   52321586    0
S3   28800 	M2  ptp3    Netwrk ESTABLISHED  8004509   38295849    0
S4   26400	M37 ptp4    Netwrk ESTABLISHED 	3534285   30490344    0
S5   28800 	M1  ptp5    Netwrk ESTABLISHED  3136302   37014991    0
S6   33600	M27 ptp6    Netwrk ESTABLISHED  7784788   31805262    0
S7   28800 	M23 ptp7    Netwrk ESTABLISHED  4316154   52130507    0
S8   21600 	M4  ptp8    Netwrk ESTABLISHED  3056758   33047779    0
S9   31200	M3  ptp9    Netwrk ESTABLISHED  6639395   40367740    0
.

.

.

ISP-PM3-1> show line0
-------------------------line0 - E1 Primary Rate ISDN-------------------

Status: UP	F1      Framing: CRC4    Encloding: HDB3 PCM: a-law
Alarms			Violations

-----------------------------	------------------------------------
Remote Alarm             0	Bipolar			  201
Receive Carrier Loss	 0	CRC4			    0
Loss of Sync		 0	E-bit			    0
				FAS bit			    0

For futher information, consult the reference manual,
Command Line Administrator's Guide.



ISP-PM3-1> show modem

Mdm    Port Status  Speed  Compression  Protocol Calls  Retrain  Disconnect
----   ---- ------  -----  -----------  -------- -----  --------  ----------

M0     S2   ACTIVE  28800  V42BIS      LAPM      2      0        NORMAL
M1     S3   ACTIVE  28800  V42BIS      LAPM      1      0        NORMAL
M2     S4   ACTIVE  33600  V42BIS      LAPM      1      0        NORMAL
M3           READY  UNKNWN   NONE      NONE      0      0        NORMAL
.

.

.

ISP-PM3-1> show m0
State: ACTIVE
Active Port: S2
Transmit Rate: 28800
Receive Rate: 28800
Connection Type: LAPM/V42BIS
Chars Sent: 8537870
Chars Received: 7563501
Retrains: 0
Renegotiations: 0
Total Calls: 3
Modem Detects: 3
Good Connects: 3
Connection Failures
No Modulation: 0
No Protocol: 0
Not Operational: 0
Total Failed: 0
Session Terminations
  Lost Carrier: 0
Normal Disconnect: 2
ISP-PM3-1> sh mc
Neighbors:
192.168.1.1	192.168.1.2

Port  	User      Host/Inet/Dest  	Type     Peer
-------	-------	---------------------	-------	------
S22 	user1      192.168.1.21    	SLAVE   192.168.1.1
VO  	user2      192.168.1.200   	VIRTUAL 192.168.1.2


For more information on debugging, consult the reference manual, Command
Line Administrator's Guide.


ISP-PM3-1>set console
To clear debug commands.
ISP-PM3-1>set debug off
ISP-PM3-1>reset console

Thank you for using Lucent products in your network.